电路板护膜笔,型号:CW3300G
品名:涂层笔、绿油笔、护膜笔,产地:美国
CircuitWorks®护膜笔是保护电路和绝缘电路板痕迹、组件和其他精密电子产品的理想选择。这种gx的丙烯酸共形涂层提供了很好的保护,防止短路、潮湿、磨损、zj和其他环境危害。允许在电路板的原型、制造和维修中容易地修复焊料掩模。
特性:为线路板提供敷型涂层,适用于修理焊层和跨线电路
更适用于不宜用热焊来解决的线路问题保护重要焊点和接触点提供绝缘保证,防止短路保护。CW2200MTP导电笔留下的银线
特点和优点
1简单易用的单组件系统,2坚硬耐用的涂层,3高介电强度有助于防止放电,4在室温下快速干燥,5防止潮湿和磨损损坏,6符合MIL-I-46058C和IPC-CC-830A的要求
注意事项:请勿接入到口、眼睛等敏感部位,如果感觉不适请就医,热固化5 - 10分钟
包装规格:CW3300 重量:4.9g
12支/盒,笔尖直径:约0.8MM
成分:聚合物保形涂料
颜色:绿色
VOC含量:630克/ L
温度范围:-67至255°F(-55~125℃)
干燥时间:<5分钟
电阻率:>1012
ohm-cm @ 50 V直流
介质击穿:>
500伏/毫升
介电常数:3-4
耗散因数:<0.001@1千赫
柔韧性:优异
耐湿性:优秀
附着力:优良
典型厚度:2-3毫升
应用:1绝缘和保护导电笔痕迹,2修复焊料掩模,3防止短路和电弧,4,覆盖线路板上的污点或者痕迹或者标志性的字体。
使用说明:
1.清洁表面
2.将笔的顶部在硬表面上轻敲以混合的球放松,用力摇动笔使材料混合
3.将笔轻轻顶到需修理的表面,用力按下软管使液体均匀流出
4.在室温下干燥5-15分钟,整个修理过程需半小时。
5.每次使用后,清洁笔尖并盖上笔帽
挤压笔身同时按下笔头,材料即可流出。挤压笔身的力量大小和按压笔头的深度,决定材料流出的量,笔头移动的速度决定线的大小。(类似涂改液的操作)可画点。可画线。
CircuitWorks Overcoat
Pens
CircuitWorks® Overcoat Pen is ideal
for protecting and insulating circuit board traces, components, and other
delicate electronics. This highly effective acrylic conformal coating provides
excellent protection against shorts, moisture, abrasion, fungus, and other
environmental hazards. Allows for easy repair of solder mask in prototype,
manufacture and repair of circuit boards.
FEATURES & BENEFITS
·Simple to use, single component
system
·Hard, durable coating
·High dielectric strength helps
prevent electrical discharge
·Dries quickly at room
temperature
·Protects against moisture and
abrasion damage
·Meets requirements of MIL-I-46058C
and IPC-CC-830A
APPLICATIONS
·Insulates and protects conductive
pen traces
·Repairs permanent solder
mask
·Prevents shorting and
arcing
------------------------CW2200MTP-------------------------------------------
品名:导电银笔
型号:CW2200MTP
产地:美国
特性:可在电路板上画出高导通的银丝线,用于跳线和屏蔽。CircuitWorks®导电笔可在电路板上即时生成高导电性银痕,用于电路板的原型制作、返工和修复。 可连接部件或者元器件、修复有缺陷的焊点或者电线、制作平滑的跳线。这种电路笔的银痕在几分钟内就干了,而且对大多数电子材料都有极好的附着力。工程师、维修技术人员和制造商会发现,CircuitWorks®导电电路笔加快了项目的完成,缩短了返工时间。
特点和优点:
可以快速画出导电的银线或者痕迹。
阀门笔尖,使用方便,下压笔尖并移动笔头即可画出导线。
低温可焊接,优越的导电性,与一般导线无异。
在室温下几分钟就干了
有细线条的尖头(MTP),笔头尺寸为0.8毫米
应用
修复线路板导线痕迹
链接线路板上的元器件及组件
CircuitWorks
Conductive Pen
CircuitWorks®
Conductive Pens make instant highly conductive silver traces on circuit boards
and are used in prototype, rework, and repair of circuit boards by linking
components, repairing defective traces, making smooth jumpers. The silver traces
of the circuit pen dry in minutes and have excellent adhesion to most electronic
materials. Engineers, repair technicians, and manufacturers will find that the
CircuitWorks® Conductive Circuit Pen speeds project completion and cuts rework
time.
FEATURES &
BENEFITS
Quickly creates
conductive silver traces
Valve pen tip for
easy applications
Solderable at low
temperatures
Superior electrical
conductivity
Dries in minutes at
room temperature
Choice of Micro Tip
(MTP) for fine lines or Standard Tip (STP) for wider lines
APPLICATIONS
Repairs
traces
Links
components
Makes smooth
jumpers
Shields
electronics