问：
如何使其不堵塞？
答：
纸板是每个复印机或可能会出现周期性的现象，纸板故障不会影响图像质量复制产品，但由于机械故障和控制系统故障。由于纸板是一种常见的故障，而每台机器表面结构设计，加工技术，组装技术，零部件质量以及其他因素的不同，在这里可作参考一些共同问题。
1，为造纸厂
（1）捻纸：
答搓纸轮老化，磨损。
湾不足的压力擦纸轮。
角纸箱（台湾），左，右与纸张差距过小，约1毫米左右正常。
d.擦纸轮双方的压力均匀，形成一方先进，同时纸倾斜。
（2）纸张：
答在纸张的尺寸不符合机器的要求。
湾前后不一致的宽度不是一个90度角。
角本文不扭曲打开。
d.反装载纸张。
2，饲养设备
（1）直属道：直属道一纸传输通道，所以不应该有喂养道垃圾和其他废弃物，和毛刺，保持清洁纸路，顺利进行，以避免卡纸的一个重要因素。
（2）喂入罗拉(Lorac)：送纸是通过喂养辊，这样变速器应以双方的压力，统一喂养辊，辊保持一致，否则势必会的文件传送过程中，造成卡纸。
3，对部分分离
（1）分离设备故障（例如，带过，空气吸口吸不到空气分离，分离的角度和不适当和不足，电压AC电荷分离位置等）。
（2）分离设备不进行定期清洗，保养和维修。
4，固定部分
（1）在压力的阴影两端热辊是不一致的方式。
（2）热辊残余碎片中（如纸片）。
（3）热定影单元清洁不好，使碳粉融化导板，阻碍了通过这份文件。
答：
楼上说，很详细，我要添加多个文件中，每个
饲料，那么有两种可能的一个静电，在阳光(sunny)下晒得到这份文件，干燥那么，还有一种可能性是，该文件是太薄，机器所需的80克的纸张，但我们通常使用的70
克答：
我的房子去年冬天，总有果酱复印机，后来开实际上在内部看住蟑螂！
Why is the regular copier paper jam?
Question:
how to make it do not jam?
Answer:
cardboard is each copier may appear or a recurring phenomenon, cardboard failure does not affect the image quality copy products, but because of mechanical failure and control system failure. As the cardboard is a common fault, and the surface structure of each machine layout, processing technology, assembly technology, the quality of parts and components as well as other factors are different, here are some common problems for reference.
1, for the paper plant
(1) twist of paper:
a. Pickup Roller aging, wear and tear.
b. insufficient pressure rubbing paper round.
c. carton (Taiwan) left and right with the paper gap is too small, the normal of about 1mm or so.
d. rub on both sides of paper round the pressure evenly, forming one side advanced, taking paper tilt.
(2) Paper:
a. the size of the paper does not meet the requirements of the machine.
b. front and rear width of the inconsistency is not a 90 degree angle.
c. paper does not twist to open.
d. anti-loaded paper.
2, feeding devices
(1) Feeder Road: Feeder Road is a paper-transport channel, so there should not be feeding tract litter and other debris, and burrs, maintaining paper Road clean, smooth is to avoid card paper important factor.
(2) feeding rollers: paper delivery is accomplished by feeding roller, so the transmission should be uniform feeding roller, roll on both sides of the pressure to be consistent, otherwise it would skew the process of transmission of paper, causing paper jam .
3, separation of part of the
(1) separation device failure (eg, strips off, air suction mouth suction less than air separation, separation angle and location of the inappropriate and insufficient voltage AC charge separation, etc.).
(2) separation device does not conduct regular cleaning, maintenance and repair.
4, fixing some of
(1) hot rollers at both ends of the pressure shadow is inconsistent manner.
(2) hot-roll the middle of residual debris (such as scraps of paper).
(3) hot fuser unit clean is not good, so that toner melt in the guide board, hindering the adoption of the paper.
Answer:
upstairs said, in great detail, I have to add each one on paper
feed more than one, then there are two possible one static electricity, drying under the sun to get the paper drying on the Well, another possibility is that the paper is too thin, the machine required 80 grams of paper, but we usually use 70 grams of
Answer:
my house last winter, there are always jam copier, and later opened a look inside actually lived in cockroach!04-12-19